ENESEAL MP/HS

EXTREME Floor Protection for EXTREME Environments

Easy to apply ENECLAD FPS seals and protects concrete floors. This extraordinary high-performance polymer composite is extremely abrasion resistant, making it ideal for heavy traffic areas in warehouses, hangars, loading docks, etc. FPS jackets the surface in a rugged, armored coating that resists forklift traffic, oil, gasoline and many common industrial chemicals.

ENECLAD FPS is a solvent-free, virtually odor-free, two-component product specifically developed to solve some of the toughest industrial floor protection problems. It is easily applied by brush, roller or squeegee to a super high-gloss finish. Non-skid aggregates can be incorporated into the ENECLAD FPS to provide a highly durable, slip resistant surface.

ENECLAD FPS high performance polymer system has been specifically formulated for new or old concrete floors. FPS produces a seamless surface that is easy to clean and easy to maintain.

Prior to applying ENECLAD FPS to concrete and / or cementitious substrates, the surface should be treated with CHEMCLAD® P4C to seal the surface, minimize outgassing and insure that optimum adhesion is obtained.

  • Traffic Resistance
  • Abrasion Resistance
  • Chemical Resistance
  • Oil Resistance
  • Detergent Resistance
  • Easy Application
  • Easy Maintenance
  • No V.O.C’s
  • No Odor

Technical Data

Volume capacity per kg.
46 in3 / 750 cc
Mixed density
0.048 lbs per in3 / 1.31 gm per cc
Coverage rate per kg. @ 12 mils / 300 microns
25 ft2 / 2.3 m2
Shelf life
Indefinite
Volume Solids
100%
Mixing ratio Base Activator
By Volume 2 1
By Weight 3 1

Colors

Tile Red

Haze Gray

Note: Other colors are available on a “special order” basis. However, there are minimum / multiple quantity requirements for such orders and there may be an increase in cost. Additionally, due to formulation restrictions, not all colors are possible for all materials. Speak to your local ENECON Sales Representative for more information.

Due to monitor / printer differences, actual colors may vary slightly from the representations appearing in this chart.

Cure Times

Ambient Temperature Working Life Touch Dry Maximum Overcoat Full Cure
59°F 15°C 90 min. 24 hrs. 48 hrs. 6 days 
77°F 25°C 70 min. 16 hrs. 24 hrs. 4 days
86°F 30°C 55 min. 8 hrs. 16 hrs. 3 days

Physical Properties

Typical Values Test Method
Compressive strength 11,000 psi 770 kg/cm2 ASTM D-695
Flexural strength 9,000 psi 630 kg/cm2 ASTM D-790
Hardness - Shore D 86 ASTM D-2240
Abrasion resistance 35 mg / 1,000 cycles ASTM D-4060
Shear Adhesion
Steel 4100 psi 287 kg/cm2 ASTM D-1002
Elcometer Adhesion - to properly prepared cementitious surfaces is
greater than the cohesive strength of the substrate.

CHEMCLAD P4C Technical Data

Theoretical coverage rate per kg. @ 3 mils
70 - 80 ft2 / 6 - 7 m2
Mixing ratio Base Activator
By Volume 2 5
By Weight 2 5
Ambient Temperature Working Life Minimum Overcoating Maximum Overcoating
41°F 5°C 120 min. 16 hrs. 48 hrs.
59°F 15°C 75 min. 12 hrs. 36 hrs.
77°F 25°C 60 min. 8 hrs. 24 hrs.
86°F 30°C 50 min. 5 hrs. 16 hrs.

Chemical Resistance

Gasoline EX  Detergent Solution EX 
Kerosene EX Trisodium Phosphate  EX
50% Anti-Freeze  EX 20% Calcium Chloride  EX
Transmission Fluid  EX 10% Hydrochloric Acid EX 
Power Steering Fluid  EX 10% Sulfuric Acid EX 
Motor Oil  EX 10% Sodium Hydroxide  EX

EX - Suitable for most applications including immersion
G - Suitable for intermittent contact, splashes, etc.

Extended Information

Ask an ENECON Tech

Fill out my online form.

Sign up for ENECON's latest Repair - Don't Replace solution

Fill out my online form.